PDA

View Full Version : Problem with pics on mugs



becky13299
10-10-2010, 02:46 PM
hi i am new to this and would be grateful for any help. we have just bought the domglobal 5 in 1 heat press initially to help my rhinestone business but as i have the other attachments thought i would give the mugs ago. we have an epson d120 with continuous bulk feed ink and on the first few mugs have had the same problem

we have tried setting the temp at 180,185, 190, 195 and have gradually increased the pressure but always heating for 310 seconds it always seems to happen around the edges but also in various other places

can anyone please tell me if they have had the same problem and how they solved it
kind regards becky[attachment=1:25h3l96u]021.JPG[/attachment:25h3l96u][attachment=0:25h3l96u]022.JPG[/attachment:25h3l96u][attachment=0:25h3l96u]022.JPG[/attachment:25h3l96u]

Justin
10-10-2010, 03:50 PM
Welcome to the forum Becky ;)

Who is the mug supplier and what paper/inks are you using?

becky13299
10-10-2010, 04:18 PM
the mugs are from bms and the ink from xpres cant remember where the paper was from

becky

thespringonion
10-10-2010, 04:25 PM
Welcome!

Can the defect be felt with fingertips (any residue on the surface?) or it's all visual?

becky13299
10-10-2010, 04:32 PM
No defects you cant feel it with your fingertips its all visual

Justin
10-10-2010, 04:39 PM
You're cooking for 310 seconds? Usual time is around 180 secs, that could be the first thing to change. temp sounds about right 185/190.

Are the marks consistent throughout prints or do they move?

becky13299
10-10-2010, 04:44 PM
the marks move not always in the same place but mainly round the edges

thespringonion
10-10-2010, 05:11 PM
Justin got it there, 310 second is too long, 180 is the norm, try that and see how it goes. Also worth a shot is to flip the mug upside down half way through pressing (90 seconds each way) in case if it's the press that's not giving an even pressure coverage.

becky13299
10-10-2010, 06:24 PM
thanks will give it a go later and let you know how i get on

JSR
10-10-2010, 06:28 PM
I don't think it's the time. While 310s is a little on the long side, I see no sign of blurring or ink migration to suggest that it's in the press for too long. Whatever effect you get from pressing for too long would affect the whole design, not just patches.

It looks like there's two issues going on here. The light print at the edge of the design on the purple mugs looks like a heat blanket issue (which will get worse if you reduce the time). The patches in the print area suggest dodgy paper (perhaps it's been left open to the atmosphere or has had water splashed on it at some stage).

I'd recommend you get a pack of brand new and trusted paper (such as TruPix) and see if that eliminates the patches. It won't eliminate the pink edge, but one thing at a a time.

That'd be my two-penneth.

Paul
10-10-2010, 08:37 PM
Hi! I would increse preasure too. try heavy. very heavy ;) can you pre - press paper before you print on it? I done that once when my paper was to "wet".

becky13299
10-10-2010, 09:02 PM
hi was just reading back through my post and must of been having a blonde moment i heat for 210 seconds not 310 !!!! :roll:
we have just done another one at 185 temp for 180 seconds and the same thing happened

Paul
10-10-2010, 09:12 PM
try pre-presed paper ;) i think its moisture in it :) ooo and incrase preasure... I have this same mug attachment as you so I know what i am talking about ;) very good press but need some preasure....

becky13299
10-10-2010, 09:28 PM
when you mean pre pressed paper do you put it in the press and heat it and at what temp and how long

Paul
10-10-2010, 09:32 PM
press it lets say... 25- 30sec at 150C let it cool down a bit then print your designe on it.

btw. make sure you print on right side of your paper ;)

logobear
14-10-2010, 11:28 PM
Try filling your mug with boiling water from the kettle. Leave it for a minute, empty, THEN press your mug.
You can tape up the artwork before warming the mug.
My suspicion is you have a cheap press with small and weak heat element, the handle sucks out heat.
You get partial sublimation.
Phil.
Ps. I prefere going to 200 or even 205 but fir a shorter time.