Hi All
I need to get hold of a small quantity of 22oz orca brand beer steins, the one with the gold rim at the top & the bottom.
Looking for the modern design with the straight handle, not the...
Type: Posts; User: MREDD
Hi All
I need to get hold of a small quantity of 22oz orca brand beer steins, the one with the gold rim at the top & the bottom.
Looking for the modern design with the straight handle, not the...
Hi All
I am looking for guidance in regards to the use of a 3d vacuum press. I have purchased one & I am currently using it to make water bottles. I don't use any wraps, I just tape the paper onto...
Hi All
I just wanted to alert the community to a potential safety issue regarding stainless steel travel mugs.
On two occasions the plastic bung or whatever you wish to call it has blown out...
Hi All
This has been posed sometime ago but with no clear answer so I am revisiting the question.
I sell the new style 22oz beer stein from Coralgraph, the one with the gold line top & bottom....
Hi All
I posted a thread recently regarding a printing problem I was having with large glass clocks, pleased to say that print issue seems to be resolved but now thrown up another problem.
I...
Hi All
I will try to explain this as best I can, I should point out that I have spoken to the Governments IPO office (Intellectual Property) they could not answer it, also the Copyright Law...
Thank you Andrew, would you suggest any pre-heating?
Hi Justin
Up to now yes preheating / prepressing for about 30 to 50 seconds, but each time I have pre-heated I have pre-heated with the frosted/chinchilla side up to the heat.
Ed
It's an Adkins swing press, so a good one.
Someone somewhere else asked which way up I presented it to the press, the answer was paper facing up to the heat platten, it has been suggested to me to...
Hi All
Does anyone have experience of sublimating large glass clocks? (30cm) Longforte reccommend 4m at 200dg
I am getting a whishy washy white blurring / ghosting in certain areas but not in...
As per my previous reply to another poster, try the yellow / gold tape, most subli firms sell it, the green tape is thicker & therefore easier to work with when applying the tape to the transfer /...
180 for 180 & what colour is your heat tape? I found the green tape can leave marks, try the yellow / gold tape it tends to iliminate marks.
Hi All
I have a BMS bought mug press (horizontal) wherby you can slide them through from one side or the other. If I turn the knob fully anti-clockwise it will just about fit, however it's a real...
Hi Justin
I wonder if this might be the problem, when I posted this question I did not offer an explanation of how I present the slate into the press. Someone asked me this this afternoon & I said...
Hi All
I have a couple of questions for those of you who work with rock slate plaques.
I use an Adkins press, sawgrass trupix paper & a Ricoh Sg3110DN printer.
Following suppliers pressing...
Hi All
I two am having this issue with coasters, I am using an Adkins press so I am fairly confident that the platten is OK
I am pre pressing for 80 at 200 & I can see moisture burning off. I...
Hi All
I have been sublimating for a couple of years now, coffee mugs down to a reasonable fine art, travel mugs getting there, but having a total mare with ceramic steins.
I have a BMS DF-18 I...
Yes understood, just seen on one youtube clip that someone says it takes 12 hours to make an i phone cover, so don't the techonolgy is there yet, I will stick to bulk buying.
Hi All
For someone who openly admits that they're technically challenged (it's an age thing!) I was fascinated by a documentary about 3D printing, I never knew it was possible to create actual...
The image should not show any signs in my experience it will give good results up to the last print prior to a cartridge being empty. Then whichever runs out it will say "Ink out" Rather than buying...
Hi All
I am not as techie as I suppose I should be so I will explain this the best I can.
I have an SG3110DN on my network which is wired by Lan into a Virgin Media hub. It works fine for a...
Ink carts are vacumm packed when you think they're going to run out they keep going & going a like duracel bunny on speed!
Hi
No there is no spring at the back, just as you say 4 springs that float the head, the handle when pressed down forces the top the unit to slide down a metal pole which seems to be free of any...
2936 Hopefully you can see from this image which was taken with the handle press down, the back spring is compressing which causes the metal plate to tilt forwards but the front, left hand side and...
Hi
There is no clear sign of a model number on the plate, just says Combo heat press, made in China