Join our Premium Membership now and save with Xpres, Listawood, Ink Experts, Ink Express and more! Just £10 per year.....Click the Membership link above.....

Search:

Type: Posts; User: wayupnorth

Page 1 of 13 1 2 3 4

Search: Search took 0.02 seconds.

  1. Never had a warping problem with coasters, even...

    Never had a warping problem with coasters, even the cheapest ones work. Table mats are a nightmare.
  2. Hope it works but my first thought is to cut a...

    Hope it works but my first thought is to cut a piece of kitchen worktop the same size as the pressure plate and stack on top of the mats. This will spread the pressure instead of concentrating it in...
  3. Replies
    2
    Views
    1,333

    Thanks for the reply, just purchased an 1810 from...

    Thanks for the reply, just purchased an 1810 from Ink Experts. Probably need to check if my Adkins beta still works after being stored for 8 years....
  4. Replies
    2
    Views
    1,333

    1810 or 2850 ?

    Just about to jump back into dye sub for low volume output. The Epson 1810 would probably be ok but is there anything to be gained from getting the 2850 which is around £100 more ?
    Cheers
  5. Replies
    14
    Views
    4,026

    Leaning toward a 2850 via Ink Experts. I have...

    Leaning toward a 2850 via Ink Experts. I have Mirage rip for my a2 Epson but probably not much use for A4, don't really want to go down the A3 sub route. Seems odd that Sawgrass would isolate a whole...
  6. Replies
    14
    Views
    4,026

    Thanks, I am finally getting back into dyesub...

    Thanks, I am finally getting back into dyesub after many years, printer choice was easy back then but a bit confused now. I have an xrite istudio so can produce my own profiles. Does this not work if...
  7. Replies
    14
    Views
    4,026

    Can print manager import a custom profile for the...

    Can print manager import a custom profile for the sg500 ?
  8. Replies
    3
    Views
    892

    I purchased one of these: ...

    I purchased one of these:

    https://www.warco.co.uk/sheet-metal-fabrication-machinery-metalwork/303009-bench-guillotine-shear-cut-sheet-metal.html

    Good finish on one edge and does not curl the...
  9. Thread: Sg400....

    by wayupnorth
    Replies
    0
    Views
    1,463

    Sg400....

    I have been keeping my SG400 fed and on standby for what seems like years and promised myself that this is the end of the road when the ink needs replacing. Switched off a couple of weeks ago and...
  10. Thread: Mouse mats

    by wayupnorth
    Replies
    5
    Views
    1,977

    Many moons ago I was making table mats from pre...

    Many moons ago I was making table mats from pre made cheap tesco mats. I used twin sided adhesive film to fix a picture to the front and self adhesive cork sheet for the back. A bit tedious as both...
  11. Thread: 3D printer

    by wayupnorth
    Replies
    2
    Views
    1,802

    Have a look on Amazon, choose your price point...

    Have a look on Amazon, choose your price point and read the reviews. Be aware that the cheaper models are probably kits but if you have any mechanical aptitude this can be rewarding. Allow a week to...
  12. Replies
    11
    Views
    3,910

    It can be very difficult to guarantee the print...

    It can be very difficult to guarantee the print will come out straight and aligned to the fold - even with a very good printer (Epson 4900). Many moons ago I was printing around 20 different scenes...
  13. Worth looking at one of the card creasing...

    Worth looking at one of the card creasing machines on eBay. Manual versions expensive and they work really well.
  14. Replies
    3
    Views
    8,395

    I presume the printer has a waste ink tank, I...

    I presume the printer has a waste ink tank, I posted a while back regarding the tank overflowing on an sg400 after I did a manual reset. Not the same of course but if it leaked then it would...
  15. Replies
    3
    Views
    16,005

    Never tried this but had thought about printing a...

    Never tried this but had thought about printing a "REJECT" slip and sublimating again over the original design. At least then people will not see the mug and think this is normal quality.
  16. Replies
    2
    Views
    6,577

    A long time ago I used a company called ppd and...

    A long time ago I used a company called ppd and purchased heavyweight paper in bulk to get the price down. At the time I had an epson+cis which was the only way to keep the cost per page low enough...
  17. Replies
    6
    Views
    26,788

    Good, just completed another for Adobe Indesign...

    Good, just completed another for Adobe Indesign which I needed to replace old dtp software. Well worth £9.95 but would never pay the full rate for any course, they seem to be around £250. If you...
  18. Replies
    6
    Views
    26,788

    I have purchased 4 courses (music, illustrator,...

    I have purchased 4 courses (music, illustrator, premiere pro). Excellent value for money at £10 each.
  19. The printer will do a maintenance check every day...

    The printer will do a maintenance check every day if left switched on. Despite only using a small amount of ink each time it is sufficient to fill the waste tank, only worth resetting the tank if you...
  20. Replies
    14
    Views
    13,245

    Bad timing as I am currently packing up...

    Bad timing as I am currently packing up everything before moving house. Only used 59mm from badgematic so cannot compare. Presume that both companies would send samples on request.
  21. Replies
    14
    Views
    13,245

    I use an interchangeable die tool from badgematic...

    I use an interchangeable die tool from badgematic (Germany) as well as 2 fixed die presses from blankbadge (UK). Not all sizes and styles available from one supplier (at the time) hence using two....
  22. Replies
    3
    Views
    13,880

    I was in a similar position a while back but...

    I was in a similar position a while back but needed to print quickly so I reset the counter. Of course there are no further warnings, slipped my mind and the tank finally overflowed. The ink makes a...
  23. Replies
    2
    Views
    1,601

    I started a few months ago with a cheap kit to...

    I started a few months ago with a cheap kit to get to know the ropes and print small engineering parts, totally addictive and the printer works nearly every day !. New printer kit arrives today...
  24. Replies
    9
    Views
    12,866

    Apologies, should have read the op.... I am using...

    Apologies, should have read the op.... I am using an SG400
  25. Replies
    9
    Views
    12,866

    No, profiles already incorporated into vpm which...

    No, profiles already incorporated into vpm which simplifies things.
Results 1 to 25 of 320
Page 1 of 13 1 2 3 4