Join our Premium Membership now and save with Xpres, Listawood, Ink Experts, Ink Express, Signzworld and more! Just £10 per year.....Click the Membership link above.....

Search:

Type: Posts; User: InkExpress

Page 1 of 11 1 2 3 4

Search: Search took 0.05 seconds.

  1. @Justin...

    @Justin You're right, the only difference is the screen. All the other internals are the same so if it saves you a few quid I'd say go with the 2600 as there really won't be any difference in speed...
  2. Hi, we are about ready to launch the ET2710, the...

    Hi, we are about ready to launch the ET2710, the ICC is made and testing has been sucessfull it is producing comparable results to the other 4 colour printers we have sold in the past.

    The ET2600...
  3. Thanks Justin :) We are working on a new ink...

    Thanks Justin :)

    We are working on a new ink set for the RICOH / SG printers that should be excellent quality and great value for money. We already do an alternative but are looking to improve on...
  4. As Simon says the pressure pay be too high, the...

    As Simon says the pressure pay be too high, the marks or blotchy effect is actually caused by the fibres of the paper. Too high pressure presses the paper fibres into the ink transfer resulting these...
  5. The L1800 is a great printer, but the lack of UK...

    The L1800 is a great printer, but the lack of UK warranty is always an issue. Especially for a reseller, as an end user I would certainly buy one and risk it. You are correct if the Eco tank...
  6. Replies
    11
    Views
    8,620

    I really rate the HL3140 Olly, like I said the...

    I really rate the HL3140 Olly, like I said the drums when they run out make it not really viable to replace but when you can just buy the whole thing again its a no brainer :)

    Alex
  7. Replies
    11
    Views
    8,620

    I run (and would recommend) a Brother HL3140CW,...

    I run (and would recommend) a Brother HL3140CW, toners are cheaper; less than £20.00 each. I had one for around 2 years before the drums needed changing at that point a new set of drums was £180.00...
  8. Thread: Pale images

    by InkExpress
    Replies
    8
    Views
    1,850

    Agreed. But the temp and time is certainly a...

    Agreed. But the temp and time is certainly a factor, even with the best consumables they'd still have issues at 160 for 120 secs :)
  9. Thread: Pale images

    by InkExpress
    Replies
    8
    Views
    1,850

    First thing to combat the pale print would be to...

    First thing to combat the pale print would be to press the mugs at 175-180 for 180 seconds this is pretty much the standard temp / time for 11oz mugs and its what I recommend to anyone I speak to...
  10. The print heads / area they print is small this...

    The print heads / area they print is small this is the main issue with the speed. For me, I am happy to wait for a quality print, but can definitely see a slow print speed getting annoying in a...
  11. Not tested the ET3700 myself, the ET2600 is an...

    Not tested the ET3700 myself, the ET2600 is an entry level printer so print speed is affect, same with the ET2710 we are testing. ET14000 appears to be a little faster but not by much. If things go...
  12. Replies
    7
    Views
    5,536

    Not really I'm afraid I have a little experience...

    Not really I'm afraid I have a little experience with wide format from using a 9880 some years back but I never actually did any servicing or repairs myself. If the chips are new I would be looking...
  13. Replies
    7
    Views
    5,536

    And you are correct, the board wont be...

    And you are correct, the board wont be disconnected if some are recognising and not others, so can't be that. Most likely the moisture affecting the chips.

    Alex
  14. Replies
    7
    Views
    5,536

    Very, I would also agree with it being damp,...

    Very, I would also agree with it being damp, moisture will build up on the electronic boards and chips causing fluctuations in the electrical signal between the cartridge chips and the printer....
  15. This was the case when they very first came out,...

    This was the case when they very first came out, but it quickly was dropped after the codes got cracked. So became useless, no codes are required to use 3rd party ink in the Ecotank printers, been...
  16. Replies
    7
    Views
    5,536

    Any chance the engineer didn't re-connect the...

    Any chance the engineer didn't re-connect the chip board ribbon cable when they were replacing the pump cap assy.? That would explain the ink recognition issue, especially if it was working fine...
  17. Thank you! Current thinking and currently in...

    Thank you! Current thinking and currently in being tested are ET14000 and ET2700 / 2710

    ET14000 - for A3; ideally I would have offered L1800 (6 colour) but they aren't available in the UK. ET14000...
  18. Good to hear you are following my thinking...

    Good to hear you are following my thinking Justin. The price of the printers are a bit higher than I'd like but it does solve all the issues of chips failing ,CISS not being fitted right, firmware...
  19. Looking into new printer models for Sublimation printing- testing and progress thread

    Hi guys,

    You may remember we did a thread on the testing and development of the Epson Surecolour SC-P600 printer for use with dye sublimation. This proved very popular and helped to show how we...
  20. Wanted SORTED! Thanks :D

    SORTED! Thanks :D
  21. Wanted Will do Mike, I will PM you later this evening or...

    Will do Mike, I will PM you later this evening or early tomorrow.

    Alex
  22. Replies
    5
    Views
    5,682

    I haven't yet tested an ET7750 but it is on my...

    I haven't yet tested an ET7750 but it is on my radar as a potential model to start to supply. Its loosely based on the XP600-900 series printers as a base with the ECO Tank on the side. The mentioned...
  23. Wanted Hi, I honestly do not know the prices are all...

    Hi, I honestly do not know the prices are all over the place on eBay. In my head I had £150.00 +cost for collecting by Parcelforce or thereabouts. If you were looking to replace with something we...
  24. Wanted RICOH SG2100N / SG3110DN printer - needs to be fully working

    We are looking for a new (haha... chance would be a fine thing!) or used and fully working RICOH SG2100N or SG3110DN printer. We have some new inks that we have had developed and want to test and...
  25. Replies
    8
    Views
    9,746

    Hi Pisquee, Thank you, we are really pleased...

    Hi Pisquee,

    Thank you, we are really pleased with it. If you're looking for a developer I cannot recommend the guy we used enough he has been an absolute star throughout and very well priced for...
Results 1 to 25 of 258
Page 1 of 11 1 2 3 4