This exactly.
as it’s against a wall and a rear loading machine it would be a nightmare.
what I don’t want to do is cut a section of worktop and then find out that I didn’t need to.
Type: Posts; User: Mrteajunkie
This exactly.
as it’s against a wall and a rear loading machine it would be a nightmare.
what I don’t want to do is cut a section of worktop and then find out that I didn’t need to.
See it's confusing lol.
It's on a stand and staying on a stand.. but imagine a kitchen worktop and the end of the worktop you have an empty space that's 2m wide and then a wall.
The printer is...
I have the spec sheet pdf from Roland with the same Info but it only shows total height not height to bottom of machine.
Hard to explain but I have a worksurface where the printer is going to...
I’m making room for the printer but need a few measurements.
Height: floor to bottom of printer clearance left hand side.
Height: as above but right hand side to bottom of waste ink bottle. ...
I have had grit type mugs from mdp before and stupidly didn’t complain about them.
They stain inside very badly :(
Oh I would have taken that 300 too.
just bought a refurbished sp300v I took the chance but sounds like I made the right choice.
sadly I don’t have room for a 540 or a spare 300.
I work in a double...
Thats what worries me at least the printheads in the sp are two separate ones not a single head and a lot cheaper to replace.
Although I print a lot more these days than I did probably 5 fold...
After months of dragging it’s heels and a lot of money spent trying to keep it going it’s finally dead.
The final straw was Friday during a large order it decided to just stop printing magenta....
Ill add that ;)
Just wait until temp is reached and then add mug and close it will start to count down.
I put the mug in when Press reaches temp.
timer starts as son as I close the press.
I thought I had described this in the 1st post?
Yes A few of my mugs have grey on them. (Cartoon dogs)
not had any issues with any colours using the method as posted in 1st post.
It’s only If I leave the workshop to answer the door or the...
it stops the sublimation process avoiding blurring or ghosting on your mugs.
I have found some mugs the print rises up the mug if I don’t dunk them leaving a Smokey type effect above the print.
Added two quick videos inserting a mug and changing mugs.
I only use a Teflon pillow when pressing an item with buttons like a polo shirt.
Can you post some images of the press with a mug inside.
it sounds like you have an incorrect element.
I have never had a single handle pop off.
I have added two videos to my press review post...
Added link for signzworld press to post.
Is the press set to *F instead of *C
Lines on the print could be a few different issues but mainly nozzle clogging or paper.
Post some images of the issue that always helps.
It will also depend on the size of your products.
An a4 printer won’t be any good if your substrate is a3.
Inkexperts sell a4 and a3 ecotanks including icc profiles.
im not running Mac so I...
Signzworld are fine they are pretty good.
it is the same press as mdp’s press.
Heating elements are cheap too.
I have different profiles for different substrates but when I first started I only used one.
An individual profile will give better results.
Only ever pressed a handful of these mugs but not had this issue myself.
Although I only use a small strip of tape on the end of the paper and not 4 strips of it.
I also only tape towards the...
I have seen a lot of bad comments when it comes to the xtool and others that are advertising EVERYWHERE you can’t go on social media without seeing an ad these days.
have a google at the reviews....
Does anyone happen to have an empty cleaning cart for a roland?
Im after 3 if possible so i can flush the inks through and clean the tubes.
Ill cover the costs of course.
Many thanks.
Welcome back
It might be me but I can’t see any difference.